 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 56F802 Data Sheet Preliminary Technical Data 56F800 16-bit Digital Signal Controllers DSP56F802 Rev. 9 01/2007 freescale.com 56F802 General Description * Up to 30 MIPS operation at 60MHz core frequency * Up to 40 MIPS operation at 80MHz core frequency * DSP and MCU functionality in a unified, C-efficient architecture * MCU-friendly instruction set supports both DSP and controller functions: MAC, bit manipulation unit, 14 addressing modes * Hardware DO and REP loops * 6-channel PWM Module with fault input * Two 12-bit ADCs (1 x 2 channel, 1 x 3 channel) * Serial Communications Interface (SCI) * Two General Purpose Quad Timers with 2 external outputs * 8K x 16-bit words (16KB) Program Flash * 1K x 16-bit words (2KB) Program RAM * 2K x 16-bit words (4KB) Data Flash * 1K x 16-bit words (2KB) Data RAM * 2K x 16-bit words (4KB) Boot Flash * JTAG/OnCETM port for debugging * On-chip relaxation oscillator * 4 shared GPIO * 32-pin LQFP Package 6 PWM Outputs Fault A0 PWMA RESET 5 JTAG/ OnCE Port VCAPC VDD 2 2 VSS* VDDA 3 Digital Reg Analog Reg VSSA 2 3 A/D1 A/D2 VREF ADC Interrupt Controller Low Voltage Supervisor Program Controller and Hardware Looping Unit Address Generation Unit Data ALU 16 x 16 + 36 36-Bit MAC Three 16-bit Input Registers Two 36-bit Accumulators Bit Manipulation Unit Quad Timer C 2 Quad Timer D or GPIO Program Memory 8188 x 16 Flash 1024 x 16 SRAM Boot Flash 2048x 16 Flash Data Memory 2048 x 16 Flash 1024 x 16 SRAM * PAB * * PDB * * * * IPBB CONTROLS 16 Relaxation Oscillator PLL XDB2 CGDB XAB1 XAB2 . * 2 SCI0 or GPIO INTERRUPT CONTROLS 16 COP/ Watchdog COP RESET MODULE CONTROLS ADDRESS BUS [8:0] DATA BUS [15:0] 16-Bit 56800 Core Application-Specific Memory & Peripherals IPBus Bridge (IPBB) *includes TCS pin which is reserved for factory use and is tied to VSS 56F802 Block Diagram 56F802 Technical Data, Rev. 9 Freescale Semiconductor 3 Part 1 Overview 1.1 56F802 Features 1.1.1 * * * * * * * * * * * * * * Processing Core Efficient 16-bit 56800 family controller engine with dual Harvard architecture As many as 40 Million Instructions Per Second (MIPS) at 80 MHz core frequency Single-cycle 16 x 16-bit parallel Multiplier-Accumulator (MAC) Two 36-bit accumulators including extension bits 16-bit bidirectional barrel shifter Parallel instruction set with unique processor addressing modes Hardware DO and REP loops Three internal address buses and one external address bus Four internal data buses and one external data bus Instruction set supports both DSP and controller functions Controller style addressing modes and instructions for compact code Efficient C compiler and local variable support Software subroutine and interrupt stack with depth limited only by memory JTAG/OnCE debug programming interface 1.1.2 * * Memory Harvard architecture permits as many as three simultaneous accesses to program and data memory On-chip memory including a low-cost, high-volume Flash solution -- 8K x 16 bit words of Program Flash -- 1K x 16-bit words of Program RAM -- 2K x 16-bit words of Data Flash -- 1K x 16-bit words of Data RAM -- 2K x 16-bit words of Boot Flash * Programmable Boot Flash supports customized boot code and field upgrades of stored code through a variety of interfaces (JTAG) 1.1.3 * * * * * Peripheral Circuits for 56F802 Pulse Width Modulator (PWM) with six PWM outputs with deadtime insertion and fault protection; supports both center- and edge-aligned modes Two 12-bit, Analog-to-Digital Converters (ADCs), 1 x 2 channel and 1 x 3 channel, which support two simultaneous conversions; ADC and PWM modules can be synchronized Two General Purpose Quad Timers with two external pins (or two GPIO) Serial Communication Interface (SCI) with two pins (or two GPIO) Four multiplexed General Purpose I/O (GPIO) pins 56F802 Technical Data, Rev. 9 4 Freescale Semiconductor 56F802 Description * * * * * * Computer-Operating Properly (COP) watchdog timer External interrupts via GPIO Trimmable on-chip relaxation oscillator External reset pin for hardware reset JTAG/On-Chip Emulation (OnCETM) for unobtrusive, processor speed-independent debugging Software-programmable, Phase Locked Loop-based frequency synthesizer for the controller core clock 1.1.4 * * * * * Energy Information Fabricated in high-density CMOS with 5V-tolerant, TTL-compatible digital inputs Uses a single 3.3V power supply On-chip regulators for digital and analog circuitry to lower cost and reduce noise Wait and Stop modes available Integrated power supervisor 1.2 56F802 Description The 56F802 is a member of the 56800 core-based family of processors. It combines, on a single chip, the processing power of a DSP and the functionality of a microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because of its low cost, configuration flexibility, and compact program code, the 56F802 is well-suited for many applications. The 56F802 includes many peripherals that are especially useful for applications such as motion control, home appliances, encoders, tachometers, limit switches, power supply and control, engine management, and industrial control for power, lighting, automation and HVAC. The 56800 core is based on a Harvard-style architecture consisting of three execution units operating in parallel, allowing as many as six operations per instruction cycle. The microprocessor-style programming model and optimized instruction set allow straightforward generation of efficient, compact code for both DSP and MCU applications. The instruction set is also highly efficient for C compilers to enable rapid development of optimized control applications. The 56F802 supports program execution from either internal or external memories. Two data operands can be accessed from the on-chip Data RAM per instruction cycle. The 56F802 also provides and up to 4 General Purpose Input/Output (GPIO) lines, depending on peripheral configuration. The 56F802 controller includes 8K words (16-bit) of Program Flash and 2K words of Data Flash (each programmable through the JTAG port) with 1K words of both Program and Data RAM. A total of 2K words of Boot Flash is incorporated for easy customer-inclusion of field-programmable software routines that can be used to program the main Program and Data Flash memory areas. Both Program and Data Flash memories can be independently bulk erased or erased in page sizes of 256 words. The Boot Flash memory can also be either bulk or page erased. A key application-specific feature of the 56F802 is the inclusion of a Pulse Width Modulator (PWM) module. This modules incorporates six complementary, individually programmable PWM signal outputs to enhance motor control functionality. Complementary operation permits programmable dead-time 56F802 Technical Data, Rev. 9 Freescale Semiconductor 5 insertion, and separate top and bottom output polarity control. The up-counter value is programmable to support a continuously variable PWM frequency. Both edge- and center-aligned synchronous pulse width control (0% to 100% modulation) are supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors), both BDC and BLDC (Brush and Brushless DC motors), SRM and VRM (Switched and Variable Reluctance Motors), and stepper motors. The PWMs incorporate fault protection with sufficient output drive capability to directly drive standard opto-isolators. A "smoke-inhibit", write-once protection feature for key parameters is also included. The PWM is double-buffered and includes interrupt control to permit integral reload rates to be programmable from 1 to 16. The PWM modules provide a reference output to synchronize the Analog-to-Digital Converters. The 56F802 incorporates two 12-bit Analog-to-Digital Converters (ADCs) with a total of five channels. A full set of standard programmable peripherals is provided that include a Serial Communications Interface (SCI), and two Quad Timers. Any of these interfaces can be used as General-Purpose Input/Outputs (GPIO) if that function is not required. An on-chip relaxation oscillator eliminates the need for an external crystal. 1.3 State of the Art Development Environment * * Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use component-based software application creation with an expert knowledge system. The Code Warrior Integrated Development Environment is a sophisticated tool for code navigation, compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards will support concurrent engineering. Together, PE, Code Warrior and EVMs create a complete, scalable tools solution for easy, fast, and efficient development. 1.4 Product Documentation The four documents listed in Table 1-1 are required for a complete description and proper design with the 56F802. Documentation is available from local Freescale distributors, Freescale semiconductor sales offices, Freescale Literature Distribution Centers, or online at www.freescale.com. Table 1-1 56F802 Chip Documentation Topic 56800E Family Manual DSP56F801/803/805/807 User's Manual 56F802 Technical Data Sheet 56F802 Errata Description Detailed description of the 56800 family architecture, and 16-bit core processor and the instruction set Detailed description of memory, peripherals, and interfaces of the 56F801, 56F802, 56F803, 56F805, and 56F807 Electrical and timing specifications, pin descriptions, and package descriptions (this document) Details any chip issues that might be present Order Number 56800EFM DSP56F801-7UM DSP56F802 56F802E 56F802 Technical Data, Rev. 9 6 Freescale Semiconductor Data Sheet Conventions 1.5 Data Sheet Conventions This data sheet uses the following conventions: OVERBAR This is used to indicate a signal that is active when pulled low. For example, the RESET pin is active when low. A high true (active high) signal is high or a low true (active low) signal is low. A high true (active high) signal is low or a low true (active low) signal is high. Signal/Symbol PIN PIN PIN PIN Logic State True False True False Signal State Asserted Deasserted Asserted Deasserted Voltage1 VIL/VOL VIH/VOH VIH/VOH VIL/VOL "asserted" "deasserted" Examples: 1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications 56F802 Technical Data, Rev. 9 Freescale Semiconductor 7 Part 2 Signal/Connection Descriptions 2.1 Introduction The input and output signals of the 56F802 are organized into functional groups, as shown in Table 2-1 and as illustrated in Figure 2-1. In Table 2-2 through Table 2-10, each table row describes the signal or signals present on a pin. Table 2-1 Functional Group Pin Allocations Functional Group Power (VDD or VDDA) Ground (VSS, VSSA, TCS) Supply Capacitors Program Control Pulse Width Modulator (PWM) Port and Fault Input Serial Communications Interface (SCI) Port1 Analog-to-Digital Converter (ADC) Port (including VREF) Quad Timer Module Port JTAG/On-Chip Emulation (OnCE) 1. Alternately, GPIO pins Number of Pins 3 4 2 1 7 2 6 2 5 Detailed Description Table 2-2 Table 2-3 Table 2-4 Table 2-5 Table 2-6 Table 2-7 Table 2-8 Table 2-9 Table 2-10 56F802 Technical Data, Rev. 9 8 Freescale Semiconductor Introduction Power Port Ground Port Power Port Ground Port VDD VSS VDDA VSSA 2 3* 1 1 Other Supply Port VCAPC 6 2 1 PWMA0-5 Fault A0 56F802 TXD0 (GPIOB0) RXD0 (GPIOB1) 1 1 SCI0 Port or GPIO 5 1 TCK TMS JTAG/OnCETM Port TDI TDO TRST 1 1 1 1 1 2 ANA2-4, ANA6-7 VREF ADCA Port TD1-2 (GPIOA1-2) Quad Timer D or GPIO 1 *includes TCS pin which is reserved for factory use and is tied to VSS RESET Program Control Figure 2-1 56F802 Signals Identified by Functional Group1 1. Alternate pin functionality is shown in parenthesis. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 9 2.2 Power and Ground Signals Table 2-2 Power Inputs No. of Pins 2 1 Signal Name VDD VDDA Signal Description Power--These pins provide power to the internal structures of the chip, and should all be attached to VDD. Analog Power--This pin is a dedicated power pin for the analog portion of the chip and should be connected to a low noise 3.3V supply. Table 2-3 Grounds No. of Pins 2 1 1 Signal Name VSS VSSA TCS Signal Description GND--These pins provide grounding for the internal structures of the chip, and should all be attached to VSS. Analog Ground--This pin supplies an analog ground. TCS--This Schmitt pin is reserved for factory use and must be tied to VSS for normal use. In block diagrams, this pin is considered an additional VSS. Table 2-4 Supply Capacitors and VPP No. of Pins 2 Signal Name VCAPC Signal Type Supply State During Reset Supply Signal Description VCAPC--Connect each pin to a 2.2 F or greater bypass capacitor in order to bypass the core logic voltage regulator (required for proper chip operation). For more information, refer to Section 5.2 56F802 Technical Data, Rev. 9 10 Freescale Semiconductor Interrupt and Program Control Signals 2.3 Interrupt and Program Control Signals Table 2-5 Program Control Signals No. of Pins 1 Signal Name RESET Signal Type Input (Schmitt) State During Reset Input Signal Description Reset--This input is a direct hardware reset on the processor. When RESET is asserted low, the controller is initialized and placed in the Reset state. A Schmitt trigger input is used for noise immunity. When the RESET pin is deasserted, the initial chip operating mode is latched from the EXTBOOT pin. The internal reset signal will be deasserted synchronous with the internal clocks, after a fixed number of internal clocks. To ensure complete hardware reset, RESET and TRST should be asserted together. The only exception occurs in a debugging environment when a hardware device reset is required and it is necessary not to reset the OnCE/JTAG module. In this case, assert RESET, but do not assert TRST. 2.4 Pulse Width Modulator (PWM) Signals Table 2-6 Pulse Width Modulator (PWMA) Signals No. of Pins 6 1 Signal Name PWMA0-5 FAULTA0 Signal Type Output Input (Schmitt) State During Reset Tri-stated Input Signal Description PWMA0-5-- These are six PWMA output pins. FAULTA0 --This fault input is used for disabling selected PWMA outputs in cases where fault conditions originate off-chip. 2.5 Serial Communications Interface (SCI) Signals Table 2-7 Serial Communications Interface (SCI0) Signals No. of Pins 1 Signal Name TXD0 GPIOB0 Signal Type Output Input/Ou tput State During Reset Input Input Signal Description Transmit Data (TXD0)--SCI0 transmit data output Port B GPIO--This pin is a General Purpose I/O (GPIO) pin that can be individually programmed as an input or output pin. After reset, the default state is SCI output. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 11 Table 2-7 Serial Communications Interface (SCI0) Signals (Continued) No. of Pins 1 Signal Name RXD0 GPIOB1 Signal Type Input Input/ Output State During Reset Input Input Signal Description Receive Data (RXD0)--SCI0 receive data input Port B GPIO--This pin is a General Purpose I/O (GPIO) pin that can be individually programmed as an input or output pin. After reset, the default state is SCI input. 2.6 Analog-to-Digital Converter (ADC) Signals Table 2-8 Analog to Digital Converter Signals No. of Pins 3 2 1 Signal Name ANA2-4 ANA6-7 VREF Signal Type Input Input Input State During Reset Input Input Input Signal Description ANA2-4--Analog inputs to ADC, channel 1 ANA6-7--Analog inputs to ADC, channel 2 VREF--Analog reference voltage. Must be set to VDDA - 0.3V for optimal performance. 2.7 Quad Timer Module Signals Table 2-9 Quad Timer Module Signals No. of Pins 2 Signal Name TD1-2 Signal Type Input/ Output Input/ Output State During Reset Input Signal Description TD1-2--Timer D Channel 1-2 GPIOA1-2 Input Port A GPIO--These pins are General Purpose I/O (GPIO) pins that can be individually programmed as input or output pins. After reset, the default state is the quad timer input. 56F802 Technical Data, Rev. 9 12 Freescale Semiconductor JTAG/OnCE 2.8 JTAG/OnCE Table 2-10 JTAG/On-Chip Emulation (OnCE) Signals No. of Pins 1 Signal Name TCK Signal Type Input (Schmitt) State During Reset Signal Description Input, pulled Test Clock Input--This input pin provides a gated clock to synchronize the low internally test logic and shift serial data to the JTAG/OnCE port. The pin is connected internally to a pull-down resistor. 1 TMS Input Input, pulled Test Mode Select Input--This input pin is used to sequence the JTAG TAP (Schmitt) high internally controller's state machine. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. Note: Always tie the TMS pin to VDD through a 2.2K resistor. 1 TDI Input Input, pulled Test Data Input--This input pin provides a serial input data stream to the (Schmitt) high internally JTAG/OnCE port. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. Output Tri-stated Test Data Output--This tri-statable output pin provides a serial output data stream from the JTAG/OnCE port. It is driven in the Shift-IR and Shift-DR controller states, and changes on the falling edge of TCK. 1 TDO 1 TRST Input Input, pulled Test Reset--As an input, a low signal on this pin provides a reset signal to the (Schmitt) high internally JTAG TAP controller. To ensure complete hardware reset, TRST should be asserted at power-up and whenever RESET is asserted. The only exception occurs in a debugging environment, since the OnCE/JTAG module is under the control of the debugger. In this case it is not necessary to assert TRST when asserting RESET. Outside of a debugging environment RESET should be permanently asserted by grounding the signal, thus disabling the OnCE/JTAG module on the device. Note: For normal operation, connect TRST directly to VSS. If the design is to be used in a debugging environment, TRST may be tied to VSS through a 1K resistor. Part 3 Specifications 3.1 General Characteristics The 56F802 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The term "5-volt tolerant" refers to the capability of an I/O pin, built on a 3.3V compatible process technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5V- compatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V 10% during normal operation without causing damage). This 5V-tolerant capability therefore offers the power savings of 3.3V I/O levels while being able to receive 5V levels without being damaged. Absolute maximum ratings given in Table 3-1 are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent damage to the device. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 13 The 56F802 DC and AC electrical specifications are preliminary and are from design simulations. These specifications may not be fully tested or guaranteed at this early stage of the product life cycle. Finalized specifications will be published after complete characterization and device qualifications have been completed. CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Table 3-1 Absolute Maximum Ratings Characteristic Supply voltage All other input voltages, excluding Analog inputs Voltage difference VDD to VDDA Voltage difference VSS to VSSA Analog Inputs ANAx, VREF Current drain per pin excluding VDD, VSS, & PWM ouputs Symbol VDD VIN VDD VSS VIN I Min VSS - 0.3 VSS - 0.3 - 0.3 - 0.3 VSS - 0.3 -- Max VSS + 4.0 VSS + 5.5V 0.3 0.3 VDDA + 0.3V 10 Unit V V V V V mA Table 3-2 Recommended Operating Conditions Characteristic Supply voltage, digital Supply Voltage, analog Voltage difference VDD to VDDA Voltage difference VSS to VSSA Symbol VDD VDDA VDD VSS Min 3.0 3.0 -0.1 -0.1 Typ 3.3 3.3 Max 3.6 3.6 0.1 0.1 Unit V V V V 56F802 Technical Data, Rev. 9 14 Freescale Semiconductor General Characteristics Table 3-2 Recommended Operating Conditions Characteristic ADC reference voltage1 Ambient operating temperature 1. VREF must be 0.3V below VDDA. Symbol VREF TA Min 2.7 -40 Typ - - Max VDDA 85 Unit V C Table 3-3 Thermal Characteristics6 Value Characteristic Comments Symbol 32-pin LQFP Unit Note s 2 2 1,2 Junction to ambient Natural convection Junction to ambient (@1m/sec) Junction to ambient Natural convection Junction to ambient (@1m/sec) Junction to case Junction to center of case I/O pin power dissipation Power dissipation Junction to center of case Four layer board (2s2p) RJA RJMA RJMA (2s2p) RJMA RJC JT P I/O PD PDMAX 50.2 47.1 38.7 C/W C/W C/W Four layer board (2s2p) 37.4 17.8 3.07 User Determined P D = (IDD x VDD + P I/O) (TJ - TA) /RJA C/W C/W C/W W W W 1,2 3 4 7 Notes: 1. 2. Theta-JA determined on 2s2p test boards is frequently lower than would be observed in an application. Determined on 2s2p thermal test board. Junction to ambient thermal resistance, Theta-JA (RJA) was simulated to be equivalent to the JEDEC specification JESD51-2 in a horizontal configuration in natural convection. Theta-JA was also simulated on a thermal test board with two internal planes (2s2p where s is the number of signal layers and p is the number of planes) per JESD51-6 and JESD51-7. The correct name for Theta-JA for forced convection or with the non-single layer boards is Theta-JMA. Junction to case thermal resistance, Theta-JC (RJC), was simulated to be equivalent to the measured values using the cold plate technique with the cold plate temperature used as the "case" temperature. The basic cold plate measurement technique is described by MIL-STD 883D, Method 1012.1. This is the correct thermal metric to use to calculate thermal performance when the package is being used with a heat sink. Thermal Characterization Parameter, Psi-JT (JT), is the "resistance" from junction to reference point thermocouple on top center of case as defined in JESD51-2. JT is a useful value to use to estimate junction temperature in steady state customer environments. 3. 4. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 15 5. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. See Section 5.1 from more details on thermal design considerations. TJ = Junction Temperature TA = Ambient Temperature 6. 7. 3.2 DC Electrical Characteristics Table 3-4 DC Electrical Characteristics Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50pF Characteristic Input high voltage (XTAL/EXTAL) Input low voltage (XTAL/EXTAL) Input high voltage (Schmitt trigger inputs)1 Input low voltage (Schmitt trigger inputs)1 Input high voltage (all other digital inputs) Input low voltage (all other digital inputs) Input current high (pullup/pulldown resistors disabled, VIN=VDD) Input current low (pullup/pulldown resistors disabled, VIN=VSS) Input current high (with pullup resistor, VIN=VDD) Input current low (with pullup resistor, VIN=VSS) Input current high (with pulldown resistor, VIN=VDD) Input current low (with pulldown resistor, VIN=VSS) Nominal pullup or pulldown resistor value Output tri-state current low Output tri-state current high Input current high (analog inputs, VIN=VDDA)2 Input current low (analog inputs, VIN=VSSA)2 Output High Voltage (at IOH) Symbol VIHC VILC VIHS VILS VIH VIL IIH IIL IIHPU IILPU IIHPD IILPD RPU, RPD IOZL IOZH IIHA IILA VOH -10 -10 -15 -15 VDD - 0.7 Min 2.25 0 2.2 -0.3 2.0 -0.3 -1 -1 -1 -210 20 -1 Typ -- -- -- -- -- -- -- -- -- -- -- -- 30 -- -- -- -- -- 10 10 15 15 -- Max 2.75 0.5 5.5 0.8 5.5 0.8 1 1 1 -50 180 1 Unit V V V V V V A A A A A A K A A A A V 56F802 Technical Data, Rev. 9 16 Freescale Semiconductor DC Electrical Characteristics Table 3-4 DC Electrical Characteristics (Continued) Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50pF Characteristic Output Low Voltage (at IOL) Output source current Output sink current PWM pin output source current3 PWM pin output sink current4 Input capacitance Output capacitance VDD supply current Run6 (80MHz Operation) Run6 (60MHz Operation) Wait7 Stop Low Voltage Interrupt, external power supply8 Low Voltage Interrupt, internal power supply9 Power on Reset10 VEIO VEIC VPOR Symbol VOL IOH IOL IOHP IOLP CIN COUT IDDT5 -- -- -- -- 2.4 2.0 -- 120 102 96 62 2.7 2.2 1.7 130 111 102 70 3.0 2.4 2.0 mA mA mA mA V V V Min -- 4 4 10 16 -- -- Typ -- -- -- -- -- 8 12 Max 0.4 -- -- -- -- -- -- Unit V mA mA mA mA pF pF 1. Schmitt Trigger inputs are: FAULTA0, TCS, TCK, TMS, TDI, RESET, and TRST 2. Analog inputs are: ANA[0:7], XTAL and EXTAL. Specification assumes ADC is not sampling. 3. PWM pin output source current measured with 50% duty cycle. 4. PWM pin output sink current measured with 50% duty cycle. 5. IDDT = IDD + IDDA (Total supply current for VDD + VDDA) 6. Run (operating) IDD measured using 8MHz clock source. All inputs 0.2V from rail; outputs unloaded. All ports configured as inputs; measured with all modules enabled. 7. Wait IDD measured using external square wave clock source (fosc = 8MHz) into XTAL; all inputs 0.2V from rail; no DC loads; less than 50pF on all outputs. CL = 20pF on EXTAL; all ports configured as inputs; EXTAL capacitance linearly affects wait IDD; measured with PLL enabled. 8. This low voltage interrupt monitors the VDDA external power supply. VDDA is generally connected to the same potential as VDD via separate traces. If VDDA drops below VEIO, an interrupt is generated. Functionality of the device is guaranteed under transient conditions when VDDA>VEIO (between the minimum specified VDD and the point when the VEIO interrupt is generated). 9. This low voltage interrupt monitors the internally regulated core power supply. If the output from the internal voltage is regulator drops below VEIC, an interrupt is generated. Since the core logic supply is internally regulated, this interrupt will not be generated unless the external power supply drops below the minimum specified value (3.0V). 56F802 Technical Data, Rev. 9 Freescale Semiconductor 17 10. Power-on reset occurs whenever the internally regulated 2.5V digital supply drops below 1.5V typical. While power is ramping up, this signal remains active for as long as the internal 2.5V is below 1.5V typical no matter how long the ramp up rate is. The internally regulated voltage is typically 100 mV less than VDD during ramp up until 2.5V is reached, at which time it self regulates. 160 IDD Digital IDD Analog IDD Total 120 IDD (mA) 80 40 0 10 20 30 40 Freq. (MHz) 50 60 70 80 Figure 3-1 Maximum Run IDD vs. Frequency (see Note 6. in Table 3-4) 3.3 AC Electrical Characteristics Timing waveforms in Section 3.3 are tested using the VIL and VIH levels specified in the DC Characteristics table. In Figure 3-2 the levels of VIH and VIL for an input signal are shown. VIH Input Signal Midpoint1 Fall Time Note: The midpoint is VIL + (VIH - VIL)/2. Low High 90% 50% 10% VIL Rise Time Figure 3-2 Input Signal Measurement References Figure 3-3 shows the definitions of the following signal states: * * Active state, when a bus or signal is driven, and enters a low impedance state Tri-stated, when a bus or signal is placed in a high impedance state 56F802 Technical Data, Rev. 9 18 Freescale Semiconductor Flash Memory Characteristics * * Data Valid state, when a signal level has reached VOL or VOH Data Invalid state, when a signal level is in transition between VOL and VOH Data1 Valid Data1 Data Invalid State Data Active Data2 Valid Data2 Data Tri-stated Data Active Data3 Valid Data3 Figure 3-3 Signal States 3.4 Flash Memory Characteristics Table 3-5 Flash Memory Truth Table Mode Standby Read Word Program Page Erase Mass Erase XE1 L H H H H YE2 L H H L L SE3 L H L L L OE4 L H L L L PROG5 L L H L L ERASE6 L L L H H MAS17 L L L L H NVSTR8 L L H H H 1. X address enable, all rows are disabled when XE = 0 2. Y address enable, YMUX is disabled when YE = 0 3. Sense amplifier enable 4. Output enable, tri-state Flash data out bus when OE = 0 5. Defines program cycle 6. Defines erase cycle 7. Defines mass erase cycle, erase whole block 8. Defines non-volatile store cycle Table 3-6 IFREN Truth Table Mode Read Word program Page erase Mass erase IFREN = 1 Read information block Program information block Erase information block Erase both blocks IFREN = 0 Read main memory block Program main memory block Erase main memory block Erase main memory block 56F802 Technical Data, Rev. 9 Freescale Semiconductor 19 Table 3-7 Flash Timing Parameters Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6V, TA = -40 to +85C, CL 50pF Characteristic Program time Erase time Mass erase time Endurance1 Data Retention1 Symbol Min 20 20 100 10,000 10 Typ - - - 20,000 30 Max - - - - - Unit us ms ms cycles years Figure Figure 3-4 Figure 3-5 Figure 3-6 Tprog* Terase* Tme* ECYC DRET The following parameters should only be used in the Manual Word Programming Mode PROG/ERASE to NVSTR set up time NVSTR hold time NVSTR hold time (mass erase) NVSTR to program set up time Recovery time Tnvs* - 5 - us Figure 3-4, Figure 3-5, Figure 3-6 Figure 3-4, Figure 3-5 Figure 3-6 Figure 3-4 Figure 3-4, Figure 3-5, Figure 3-6 Figure 3-4 Tnvh* Tnvh1* Tpgs* Trcv* - - - - 5 100 10 1 - - - - us us us us Cumulative program HV period2 Program hold time3 Address/data set up time3 Address/data hold time3 Thv Tpgh Tads Tadh - 3 - ms - - - - - - - - - Figure 3-4 Figure 3-4 Figure 3-4 1. One Cycle is equal to an erase program and read. 2. Thv is the cumulative high voltage programming time to the same row before next erase. The same address cannot be programmed twice before next erase. 3. Parameters are guaranteed by design in smart programming mode and must be one cycle or greater. *The Flash interface unit provides registers for the control of these parameters. 56F802 Technical Data, Rev. 9 20 Freescale Semiconductor Flash Memory Characteristics IFREN XADR XE Tadh YADR YE DIN Tads PROG Tnvs Tprog Tpgh NVSTR Tpgs Thv Tnvh Trcv Figure 3-4 Flash Program Cycle IFREN XADR XE YE=SE=OE=MAS1=0 ERASE Tnvs NVSTR Tnvh Terase Trcv Figure 3-5 Flash Erase Cycle 56F802 Technical Data, Rev. 9 Freescale Semiconductor 21 IFREN XADR XE MAS1 YE=SE=OE=0 ERASE Tnvs NVSTR Tnvh1 Tme Trcv Figure 3-6 Flash Mass Erase Cycle 3.5 Clock Operation The 56F802 device clock is derived from an on-chip relaxation oscillator. The internal PLL generates a master reference frequency that determines the speed at which chip operations occur. The PRECS bit in the PLLCR (phase-locked loop control register) word (bit 2) must be set to 0 for internal oscillator use. 3.5.1 Use of On-Chip Relaxation Oscillator The 56F802 internal relaxation oscillator provides the chip clock without the need for an external crystal or ceramic resonator. The frequency output of this internal oscillator can be corrected by adjusting the 8-bit IOSCTL (internal oscillator control) register. Each bit added or deleted changes the output frequency of the oscillator allowing incremental adjustment until the desired frequency is achieved. Figures 9 and 10 show the typical characteristics of the 56F802 relaxation oscillator with respect to temperature and trim value. During factory production test, an oscillator calibration procedure is executed which determines an optimum trim value for a given device (8MHz at 25oC). This optimum trim value is then stored at address $103F in the Data Flash Information Block and recalled during a trim routine in the boot sequence (executed after power-up and RESET). This trim routine automatically sets the oscillator frequency by programming the IOSCTL register with the optimum trim value. 56F802 Technical Data, Rev. 9 22 Freescale Semiconductor Clock Operation Due to the inherent frequency tolerances required for SCI communication, changing the factory-trimmed oscillator frequency is not recommended. If modification of the Boot Flash contents are required, code must be included which retrieves the optimum trim value (from address $103F in the Data Flash Information Block) and writes it to the IOSCTL register. Note that the IFREN bit in the Data Flash control register must be set in order to read the Data Flash Information Block. Table 3-8 Relaxation Oscillator Characteristics Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C Characteristic Frequency Accuracy1 Frequency Drift over Temp Frequency Drift over Supply 1. Over full temperature range. Symbol f f/t f/V Min -- -- -- Typ +2 +0.1 0.1 Max +5 -- -- Unit % %/oC %/V 8.4 8.3 Output Frequency 8.2 8.1 8.0 7.9 7.8 -40 -25 -5 15 35 55 75 85 Temperature (oC) Figure 3-7 Typical Relaxation Oscillator Frequency vs. Temperature (Trimmed to 8MHz @ 25oC) 56F802 Technical Data, Rev. 9 Freescale Semiconductor 23 11 10 9 8 7 6 5 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Figure 3-8 Typical Relaxation Oscillator Frequency vs. Trim Value @ 25oC 3.5.2 Phase Locked Loop Timing Table 3-9 PLL Timing Characteristic Symbol fosc fout/2 tplls tplls Min 4 40 -- -- Typ 8 -- 10 100 Max 10 803 -- 200 Unit MHz MHz ms ms Frequency for the PLL1 PLL output frequency2 PLL stabilization time4 0o to +85oC PLL stabilization time4 -40o to 0oC 1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly. The PLL is optimized for 8MHz input crystal. 2. ZCLK may not exceed 80MHz. For additional information on ZCLK and fout/2, please refer to the OCCS chapter in the User Manual. ZCLK = fop 3. Will not exceed 60MHz for the DSP56F802TA60 device. 4. This is the minimum time required after the PLL setup is changed to ensure reliable operation. 56F802 Technical Data, Rev. 9 24 Freescale Semiconductor Reset, Stop, Wait, Mode Select, and Interrupt Timing 3.6 Reset, Stop, Wait, Mode Select, and Interrupt Timing Table 3-10 Reset, Stop, Wait, Mode Select, and Interrupt Timing1, 3 Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50pF Characteristic RESET Assertion to Address, Data and Control Signals High Impedance Minimum RESET Assertion Duration2 OMR Bit 6 = 0 OMR Bit 6 = 1 RESET De-assertion to First External Address Output Edge-sensitive Interrupt Request Width Symbol tRAZ tRA Min -- Max 21 Unit ns 275,000T 128T 33T 1.5T -- -- 34T -- ns ns ns ns tRDA tIRW 1. In the formulas, T = clock cycle. For an operating frequency of 80MHz, T = 12.5ns. 2. Circuit stabilization delay is required during reset when using an external clock or crystal oscillator in two cases: * After power-on reset * When recovering from Stop state 3. Parameters listed are guaranteed by design. General Purpose I/O Pin tIG IRQA b) General Purpose I/O Figure 3-9 External Level-Sensitive Interrupt Timing 56F802 Technical Data, Rev. 9 Freescale Semiconductor 25 3.7 Quad Timer Timing Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50pF Characteristic Timer input period Timer input high/low period Timer output period Timer output high/low period 1. Table 3-11 Timer Timing1, 2 Symbol PIN PINHL POUT POUTHL Min 4T+6 2T+3 2T 1T Max -- -- -- -- Unit ns ns ns ns In the formulas listed, T = clock cycle. For 80MHz operation, T = 12.5 ns. 2. Parameters listed are guaranteed by design. Timer Inputs PIN PINHL PINHL Timer Outputs POUT POUTHL POUTHL Figure 3-10 Timer Timing 56F802 Technical Data, Rev. 9 26 Freescale Semiconductor Serial Communication Interface (SCI) Timing 3.8 Serial Communication Interface (SCI) Timing Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50pF Characteristic Baud Rate1 RXD2 Pulse Width TXD3 Pulse Width Symbol BR RXDPW TXDPW Min Max (fMAX*2.5)/(80) 1.04/BR 1.04/BR Unit Mbps ns ns Table 3-12 SCI Timing4 -- 0.965/BR 0.965/BR 1. fMAX is the frequency of operation of the system clock in MHz. 2. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1. 3. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1. 4. Parameters listed are guaranteed by design. RXD SCI receive data pin (Input) RXDPW Figure 3-11 RXD Pulse Width TXD SCI receive data pin (Input) TXDPW Figure 3-12 TXD Pulse Width 56F802 Technical Data, Rev. 9 Freescale Semiconductor 27 3.9 Analog-to-Digital Converter (ADC) Characteristics Table 3-13 ADC Characteristics Characteristic ADC input voltages Resolution Integral Non-Linearity3 Differential Non-Linearity Monotonicity ADC internal clock5 Conversion range Power-up time Conversion time Sample time Input capacitance Gain Error (transfer gain)5 Offset Voltage5 Total Harmonic Distortion5 Signal-to-Noise plus Distortion5 Effective Number of Bits5 Spurious Free Dynamic Range5 Spurious Free Dynamic Range ADC Quiescent Current (both ADCs) VREF Quiescent Current (both ADCs) fADIC RAD tADPU tADC tADS CADI EGAIN VOFFSET THD SINAD ENOB SFDR SFDR IADC IVREF 0.5 VSSA -- -- -- -- 1.00 +10 55 54 8.5 60 65 -- -- Symbol VADCIN RES INL DNL Min 01 12 -- -- Typ -- -- +/- 4 +/- 0.9 GUARANTEED -- -- 2.5 6 1 5 1.10 +230 60 56 9.5 65 70 50 12 5 VDDA -- -- -- -- 1.15 +325 -- -- -- -- -- -- 16.5 MHz V msec tAIC cycles6 tAIC cycles6 pF6 -- mV dB -- bit dB dB mA mA Max VREF2 12 +/- 5 +/- 1 Unit V Bits LSB4 LSB3 1. For optimum ADC performance, keep the minimum VADCIN value > 250mV. Inputs less than 250mV volts may convert to a digital output code of 0 or cause erroneous conversions. 2. VREF must be equal to or less than VDDA - 0.3V and must be greater than 2.7V. 3. Measured in 10-90% range. 4. LSB = Least Significant Bit. 5. Guaranteed by characterization. 6. tAIC = 1/fADIC 56F802 Technical Data, Rev. 9 28 Freescale Semiconductor JTAG Timing ADC analog input 3 1 2 4 1. Parasitic capacitance due to package, pin to pin, and pin to package base coupling. (1.8pf) 2. Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing. (2.04pf) 3. Equivalent resistance for the ESD isolation resistor and the channel select mux. (500 ohms) 4. Sampling capacitor at the sample and hold circuit. Capacitor 4 is normally disconnected from the input and is only connected to it at sampling time. (1pf) Figure 3-13 Equivalent Analog Input Circuit 3.10 JTAG Timing Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF Characteristic TCK frequency of operation2 TCK cycle time TCK clock pulse width TMS, TDI data setup time TMS, TDI data hold time TCK low to TDO data valid TCK low to TDO tri-state TRST assertion time Symbol fOP tCY tPW tDS tDH tDV tTS tTRST Min DC 100 50 0.4 1.2 -- -- 50 Max 10 -- -- -- -- 26.6 23.5 -- Unit MHz ns ns ns ns ns ns ns Table 3-14 JTAG Timing 1, 3 1. Timing is both wait state and frequency dependent. For the values listed, T = clock cycle. For 80MHz operation, T = 12.5ns. 2. TCK frequency of operation must be less than 1/8 the processor rate. 3. Parameters listed are guaranteed by design. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 29 tCY tPW VIH tPW VM TCK (Input) VM = VIL + (VIH - VIL)/2 VM VIL Figure 3-14 Test Clock Input Timing Diagram TCK (Input) TDI TMS (Input) TDO (Output) tTS tDS tDH Input Data Valid tDV Output Data Valid TDO (Output) tDV TDO (Output) Output Data Valid Figure 3-15 Test Access Port Timing Diagram TRST (Input) tTRST Figure 3-16 TRST Timing Diagram 56F802 Technical Data, Rev. 9 30 Freescale Semiconductor Package and Pin-Out Information 56F802 Part 4 Packaging 4.1 Package and Pin-Out Information 56F802 This section contains package and pin-out information for the 32-pin LQFP configuration of the 56F802. VCAPC1 PWMA3 PWMA2 PWMA1 PWMA0 ANA7 ANA6 PWMA4 PWMA5 ORIENTATION MARK PIN 25 PIN 1 ANA4 ANA3 VREF ANA2 TD1 TD2 FAULTA0 TXDO VSS VSS VDD RXD0 VDD PIN 9 PIN 17 VSSA VDDA TCS TCK TMS TRST TDI TDO Figure 4-1 Top View, 56F802 32-pin LQFP Package 56F802 Technical Data, Rev. 9 Freescale Semiconductor 31 VCAPC2 RESET Table 4-1 56F802 Pin Identification by Pin Number Pin No. 1 2 3 4 5 6 7 8 Signal Name PWMA4 PWMA5 TD1 TD2 TXDO VSS VDD RXD0 Pin No. 9 10 11 12 13 14 15 16 Signal Name TCS TCK TMS TDI VCAPC2 TDO TRST RESET Pin No. 17 18 19 20 21 22 23 24 Signal Name VDDA VSSA VDD VSS FAULTA0 ANA2 VREF ANA3 Pin No. 25 26 27 28 29 30 31 32 Signal Name ANA4 ANA6 ANA7 PWMA0 VCAPC1 PWMA1 PWMA2 PWMA3 56F802 Technical Data, Rev. 9 32 Freescale Semiconductor Package and Pin-Out Information 56F802 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE A, B AND D TO BE DETERMINED AT DATUM PLANE H. 4. DIMENSIONS D AND E TO BE DETERMINED AT SEATING PLANE C. 5. DIMENSIONS b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE MAXIMUM b DIMENSION BY MORE THEN 0.08 MM. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSION AND ADJACENT LEAD OR PROTURSION: 0.07 MM. 6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 MM PER SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE DIMENSIONS INCLUDING MOLD MISMATCH. 7. EXACT SHAPE OF EACH CORNER IS OPTIONAL. 8. THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.1 MM AND 0.25 MM FROM THE LEAD TIP. DIM A A1 A2 b b1 c c1 D D1 e E E1 L L1 O O1 R1 R2 S MILLIMETERS MIN MAX 1.40 1.60 0.15 0.05 1.45 1.35 0.45 0.30 0.30 0.40 0.09 0.20 0.09 0.16 9.00 BSC 7.00 BSC 0.80 BSC 9.00 BSC 7.00 BSC 0.50 0.70 1.00 REF 0 7 12 REF 0.08 0.20 0.08 -0.20 REF Figure 4-2 32-pin LQFP Mechanical Information (Case 873A) Please see www.freescale.com for the most current case outline. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 33 Part 5 Design Considerations 5.1 Thermal Design Considerations An estimation of the chip junction temperature, TJ, in C can be obtained from the equation: Equation 1: TJ = T A + ( P D x RJA ) Where: TA = ambient temperature C RJA = package junction-to-ambient thermal resistance C/W PD = power dissipation in package Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and a case-to-ambient thermal resistance: Equation 2: RJA = R JC + R CA Where: RJA = package junction-to-ambient thermal resistance C/W RJC = package junction-to-case thermal resistance C/W RCA = package case-to-ambient thermal resistance C/W RJC is device-related and cannot be influenced by the user. The user controls the thermal environment to change the case-to-ambient thermal resistance, RCA. For example, the user can change the air flow around the device, add a heat sink, change the mounting arrangement on the Printed Circuit Board (PCB), or otherwise change the thermal dissipation capability of the area surrounding the device on the PCB. This model is most useful for ceramic packages with heat sinks; some 90% of the heat flow is dissipated through the case to the heat sink and out to the ambient environment. For ceramic packages, in situations where the heat flow is split between a path to the case and an alternate path through the PCB, analysis of the device thermal performance may need the additional modeling capability of a system level thermal simulation tool. The thermal performance of plastic packages is more dependent on the temperature of the PCB to which the package is mounted. Again, if the estimations obtained from RJA do not satisfactorily answer whether the thermal performance is adequate, a system level model may be appropriate. Definitions: A complicating factor is the existence of three common definitions for determining the junction-to-case thermal resistance in plastic packages: * Measure the thermal resistance from the junction to the outside surface of the package (case) closest to the chip mounting area when that surface has a proper heat sink. This is done to minimize temperature variation across the surface. 56F802 Technical Data, Rev. 9 34 Freescale Semiconductor Electrical Design Considerations * * Measure the thermal resistance from the junction to where the leads are attached to the case. This definition is approximately equal to a junction to board thermal resistance. Use the value obtained by the equation (TJ - TT)/PD where TT is the temperature of the package case determined by a thermocouple. The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire. When heat sink is used, the junction temperature is determined from a thermocouple inserted at the interface between the case of the package and the interface material. A clearance slot or hole is normally required in the heat sink. Minimizing the size of the clearance is important to minimize the change in thermal performance caused by removing part of the thermal interface to the heat sink. Because of the experimental difficulties with this technique, many engineers measure the heat sink temperature and then back-calculate the case temperature using a separate measurement of the thermal resistance of the interface. From this case temperature, the junction temperature is determined from the junction-to-case thermal resistance. 5.2 Electrical Design Considerations CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Use the following list of considerations to assure correct operation: * * Provide a low-impedance path from the board power supply to each VDD pin on the controller, and from the board ground to each VSS (GND) pin. The minimum bypass requirement is to place 0.1 F capacitors positioned as close as possible to the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better performance tolerances. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 35 * * * * Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND) pins are less than 0.5 inch per capacitor lead. Bypass the VDD and VSS layers of the PCB with approximately 100 F, preferably with ceramic or tantalum capacitors which tend to provide better performance tolerances. Because the controller's output signals have fast rise and fall times, PCB trace lengths should be minimal. Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance. This is especially critical in systems with higher capacitive loads that could create higher transient currents in the VDD and GND circuits. Take special care to minimize noise levels on the VREF, VDDA and VSSA pins. Designs that utilize the TRST pin for JTAG port or OnCE module functionality (such as development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as well as a means to assert TRST independently of RESET. TRST must be asserted at power up for proper operation. Designs that do not require debugging functionality, such as consumer products, TRST should be tied low. Because the Flash memory is programmed through the JTAG/OnCE port, designers should provide an interface to this port to allow in-circuit Flash programming. * * * 56F802 Technical Data, Rev. 9 36 Freescale Semiconductor Electrical Design Considerations Part 6 Ordering Information Table 6-1 lists the pertinent information needed to place an order. Consult a Freescale Semiconductor sales office or authorized distributor to determine availability and to order parts. Table 6-1 56F802 Ordering Information Part 56F802 56F802 Supply Voltage 3.0-3.6 V 3.0-3.6 V Package Type Low Profile Plastic Quad Flat Pack (LQFP) Low Profile Plastic Quad Flat Pack (LQFP) Pin Count 32 32 Ambient Frequency (MHz) 80 60 Order Number DSP56F802TA80 DSP56F802TA60 56F802 56F802 3.0-3.6 V 3.0-3.6 V Low Profile Plastic Quad Flat Pack (LQFP) Low Profile Plastic Quad Flat Pack (LQFP) 32 32 80 60 DSP56F802TA80E* DSP56F802TA60E* *This package is RoHS compliant. 56F802 Technical Data, Rev. 9 Freescale Semiconductor 37 56F802 Technical Data, Rev. 9 38 Freescale Semiconductor Electrical Design Considerations 56F802 Technical Data, Rev. 9 Freescale Semiconductor 39 How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064, Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. This product incorporates SuperFlash(R) technology licensed from SST. (c) Freescale Semiconductor, Inc. 2005. All rights reserved. DSP56F802 Rev. 9 01/2007 |
Price & Availability of DSP56F802TA80E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |